| CORVETTE DASH & STEERING WHEEL INSTALLATION |
| STEERING WHEEL PULLER YOU SHOULD NOT NEED A WHEEL PULLER FOR A C6 STEERING WHEEL. YOU SHOULD BE ABLE TO LOOSEN THE LOCK NUT AND JUST WIGGLE THE WHEEL OFF. USE A WHEEL PULLER WITH LEGS IF DO YOU USE ONE. |
| PLACE LEGS INTO OVAL HOLES ON EACH SIDE OF THE NUT AND TWIST THE FEET ON THE LEGS TOWARDS THE CENTER OF THE WHEEL. TIGHTEN UNTIL IT COMES LOOSE. |
| CALL 714-585-8001 IF YOU NEED HELP |
#5) POWER DOOR LOCK BEZEL
#18) POWER LOCK BEZEL W/ SEAT MEMORY
#8) POWER WINDOW BEZEL
#13) DOOR HANDLE
#15) POWER DOOR OPENER BEZEL
#18) POWER LOCK BEZEL W/ SEAT MEMORY
#8) POWER WINDOW BEZEL
#13) DOOR HANDLE
#15) POWER DOOR OPENER BEZEL
2008 & UP (2 PIECE CONSOLE)
C6 DOOR PANEL
| TERMS AND CONDITIONS WE ARE NOT RESPONSIBLE FOR ERRORS AND OMISSIONS IN THE INSTALLATION INSTRUCTIONS ON THIS WEB SITE. WE ARE NOT LIABLE OR WILL NOT PAY FOR ANY COST INVOLVING DAMAGE, REPAIRS OR INJURY. GO TO A GM DEALER OR INSTALL AT YOUR OWN RISK. USE CAUTION WHEN INSTALLING DUE TO THE EXTRA THICKNESS OF THE FINISH ON THE FACTORY PARTS. SOME FILING OR SANDING MAY BE NEEDED FOR PROPER FIT. |
SEE AIRBAG REMOVAL PICTURES BELOW.
AIRBAG REMOVAL
DISCONNECT NEGATIVE BATTERY CABLE 20
MINUTES BEFORE REMOVING OR CONNECTING
THE AIR BAG.
TAKE BLUNT TOOL OR A 1/8" TO 9/64" HEX ALLEN
WRENCH AND MARK IT 3/4" FROM THE END (SEEN
WITH BLUE TAPE). PUSH IN THE HOLE 3/4" TO
FIND SPRING CLIP AND THEN PUSH IN UNTIL AIR
BAG POPS
LOOSE. REPEAT ON OTHER SIDE.
MINUTES BEFORE REMOVING OR CONNECTING
THE AIR BAG.
TAKE BLUNT TOOL OR A 1/8" TO 9/64" HEX ALLEN
WRENCH AND MARK IT 3/4" FROM THE END (SEEN
WITH BLUE TAPE). PUSH IN THE HOLE 3/4" TO
FIND SPRING CLIP AND THEN PUSH IN UNTIL AIR
BAG POPS
LOOSE. REPEAT ON OTHER SIDE.
1) MARK TOOL AT
3/4" FROM THE END
3/4" FROM THE END
2) PUSH ALLEN WRENCH IN HOLE 3/4" TO FINDTHE SPRING
CLIP, THEN PUSH TO RELEASE AIR BAG. REPEAT ON OTHER SIDE.
CLIP, THEN PUSH TO RELEASE AIR BAG. REPEAT ON OTHER SIDE.
THE STEERING WHEEL SPOKES CAN
BE REMOVED WITHOUT
DISCONNECTING THE AIRBAG.
REMOVE ONE SCREW FROM EACH
SPOKE. DISCONNECT SWITCHES
(IF YOUR WHEEL HAS THEM).
BE REMOVED WITHOUT
DISCONNECTING THE AIRBAG.
REMOVE ONE SCREW FROM EACH
SPOKE. DISCONNECT SWITCHES
(IF YOUR WHEEL HAS THEM).
| AIRBAG REMOVAL DISCONNECT NEGATIVE BATTERY CABLE 20 MINUTES BEFORE CONNECTING OR DISCONNECTING THE AIR BAG. RELEASE THE CPA RETAINER (SHOWN IN YELLOW). DISCONNECT THE ELECTRICAL CONNECTORS. |
STEERING WHEEL SPOKE REMOVAL
| READ TERMS & CONDITIONS AT THE BOTTOM BEFORE INSTALLING PARTS. USE CAUTION WHEN INSTALLING DUE TO THE EXTRA THICKNESS OF THE FINISH ON THE FACTORY PARTS. SOME FILING OR SANDING MAY BE NEEDED FOR PROPER FIT. |
Check the clips on the back and top of the
instrument cluster to make sure they are still
attached to the instrument cluster
and not stuck in the dash.
instrument cluster to make sure they are still
attached to the instrument cluster
and not stuck in the dash.
Make sure all metal clips are still attached to the radio
bezel and not stuck in the clip holes.
bezel and not stuck in the clip holes.
| PART #7) CENTER CONSOLE DRINK HOLDER/SHIFTER TRIM OR CHROME RING INSTALLATION REMOVE THE DRINK HOLDER AND SCREWS FROM THE BOTTOM OF THE CONSOLE. USE DREMEL TOOL OR FILE TO LOOSEN THE FACTORY HEAT WELDS. REATTACH WITH PLASTIC GLUE AND SCREWS. USE CAUTION WHEN INSTALLING DUE TO THE EXTRA THICKNESS OF THE FINISH ON THE FACTORY PARTS. SOME FILING OR SANDING MAY BE NEEDED FOR PROPER FIT. |
PART # 7) SEE BELOW
INSTRUCTION
INSTRUCTION
REMOVE 2 SCREWS
UNDER DOOR HANDLE
USE TOOL TO PRY THE
DOOR PANEL LOOSE ALONG THE
BOTTOM AND REAR OF PANEL
(SEE THE SEVEN WHITE DOOR
PANEL FASTENERS ALONG THE
BOTTOM AND REAR OF THE
PANEL BELOW)
UNPLUG WIRES TO DOOR
SWITCHES.
LIFT THE DOOR UP AND OFF
UNDER DOOR HANDLE
USE TOOL TO PRY THE
DOOR PANEL LOOSE ALONG THE
BOTTOM AND REAR OF PANEL
(SEE THE SEVEN WHITE DOOR
PANEL FASTENERS ALONG THE
BOTTOM AND REAR OF THE
PANEL BELOW)
UNPLUG WIRES TO DOOR
SWITCHES.
LIFT THE DOOR UP AND OFF
POWER LOCK BEZEL UNDER SPEAKER
